Do you find yourself looking for advice about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily available, the project can relocate immediately; if you need to open a wall surface to eliminate the old bathtub as well as place the brand-new tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub and also set in the brand-new one. See to it you have qualified yourself for the job as well as fit trying it. Instead of working with a contractor to take over a halfway-completed task, it is better to think about employing one before you start. Opportunities are you might need a specialist plumber to make tube links.
This write-up will assist you set up a new bath tub in your shower room if you have actually already purchased a new bathtub and also don't need to transform the plan of your previous supply of water pipes.
Your devices and also product list need to consist of the following:
Getting ready for the Installation
To start with, the supporting framework provided with the bath should be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps system to avoid pressure on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its last placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, then the first thing you need to do is detach the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be fairly troublesome because of the restricted gain access to that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly come from the pipes. Once the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the needed placement. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the tub till the spirit level checks out degree.
To set up taps, fit the bottom of the furthest flexible tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water supply and inspect all joints and brand-new pipework for leakages and also tighten them if required. Fill up the bathtub and also inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's user's manual. Tiling and securing around the bathtub ought to wait till the tub has actually been utilized a minimum of once as this will certainly resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washing machines are in place in between the tap as well as the sink. Protect the tap in position with the manufacturer offered backnut. As soon as the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former type must be linked to the tap finishes first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split an inflexible seal, causing the water to permeate the wall surface between the bath as well as the tiling, causing problems with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealant can break relatively early if you do not take into consideration this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the marketplace. It is suggested to fit the floor tiles using water-resistant or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our part on How to Install a Bathtub Yourself. Thank you for spending some time to browse our article. Sharing is nice. Who knows, you may be doing someone a favor. Thanks a lot for your time. Don't hesitate to pay a visit to our website back soon.
Schedule Free Estimate